Results: 1-25/461
Authors:
PIETRZAK K
Citation: K. Pietrzak, JOINING OF CARBON FIBER-COPPER COMPOSITE TO METALS, Journal of materials processing technology, 55(3-4), 1995, pp. 129-133
Authors:
SZOTA JG
Citation: Jg. Szota, STEEL WIRE GALVANIZING BY THE VERT-DOWN METHOD, Journal of materials processing technology, 55(3-4), 1995, pp. 134-139
Authors:
ABDELAZIM AN
SHASH Y
MOSTAFA SF
YOUNAN A
Citation: An. Abdelazim et al., AGING BEHAVIOR OF 2024-AL ALLOY REINFORCED WITH AL2O3 PARTICLES, Journal of materials processing technology, 55(3-4), 1995, pp. 140-145
Authors:
REES DWA
Citation: Dwa. Rees, INSTABILITY LIMITS TO THE FORMING OF SHEET METALS, Journal of materials processing technology, 55(3-4), 1995, pp. 146-153
Authors:
LI YY
LUO JM
LUO ZQ
XIAO ZY
NGAI TL
Citation: Yy. Li et al., THE MICROSTRUCTURE AND WEAR MECHANISM OF A NOVEL HIGH-STRENGTH, WEAR-RESISTANT ZINC ALLOY (ZMJ), Journal of materials processing technology, 55(3-4), 1995, pp. 154-161
Authors:
HAMID AA
ALI Y
Citation: Aa. Hamid et Y. Ali, EXPERIMENTAL-DETERMINATION OF DYNAMIC FORCES DURING TRANSIENT ORTHOGONAL CUTTING, Journal of materials processing technology, 55(3-4), 1995, pp. 162-170
Authors:
DING YQ
YAN Y
MCILHAGGER R
BROWN D
Citation: Yq. Ding et al., COMPARISON OF THE FATIGUE BEHAVIOR OF 2-D AND 3-D WOVEN FABRIC REINFORCED COMPOSITES, Journal of materials processing technology, 55(3-4), 1995, pp. 171-177
Authors:
WEAIRE D
COUGHLAN S
FORTES AM
Citation: D. Weaire et al., THE MODELING OF LIQUID AND SOLID FOAMS, Journal of materials processing technology, 55(3-4), 1995, pp. 178-185
Authors:
HAQUE MM
YOUNG JM
Citation: Mm. Haque et Jm. Young, PRODUCTION OF SPHEROIDAL GRAPHITE ALUMINUM CAST-IRON AND THE FACTORS AFFECTING IT, Journal of materials processing technology, 55(3-4), 1995, pp. 186-192
Authors:
HAQUE MM
Citation: Mm. Haque, EFFECTS OF STRONTIUM ON THE STRUCTURE AND PROPERTIES OF ALUMINUM-SILICON ALLOYS, Journal of materials processing technology, 55(3-4), 1995, pp. 193-198
Authors:
ABDELAZIM AN
SHASH Y
MOSTAFA SF
YOUNAN A
Citation: An. Abdelazim et al., CASTING OF 2024-AL ALLOY REINFORCED WITH AL2O3 PARTICLES, Journal of materials processing technology, 55(3-4), 1995, pp. 199-205
Authors:
COLREAVY J
SCANTLEBURY JD
Citation: J. Colreavy et Jd. Scantlebury, ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY TO MONITOR THE INFLUENCE OF SURFACE PREPARATION ON THE CORROSION CHARACTERISTICS OF MILD-STEEL MAG WELDS, Journal of materials processing technology, 55(3-4), 1995, pp. 206-212
Authors:
GRONOSTAJSKI J
ZIMNIAK Z
Citation: J. Gronostajski et Z. Zimniak, A FEW METHODS OF ANALYTICAL CALCULATION OF FORMING-LIMIT CURVES, Journal of materials processing technology, 55(3-4), 1995, pp. 213-217
Authors:
BROWNE DJ
BATTIKHA E
Citation: Dj. Browne et E. Battikha, OPTIMIZATION OF ALUMINUM SHEET FORMING USING A FLEXIBLE DIE, Journal of materials processing technology, 55(3-4), 1995, pp. 218-223
Authors:
BERNINI U
MALINCONICO M
MARTUSCELLI E
MORMILE P
NOVELLINO A
RUSSO P
VOLPE MG
Citation: U. Bernini et al., ULTRA-TOUGH SYNTHETIC GLASSES MADE BY REACTIVE BLENDING OF PMMA AND EVA RUBBERS - OPTOTHERMAL CHARACTERIZATION, Journal of materials processing technology, 55(3-4), 1995, pp. 224-228
Authors:
MESHKOV VV
KHOLODILOV OV
SVIRIDENOK AI
Citation: Vv. Meshkov et al., ON THE FRACTURE OF REINFORCED THERMOPLASTICS, Journal of materials processing technology, 55(3-4), 1995, pp. 229-233
Authors:
RYBNIKOV AI
TCHIZHIK AA
OGURTSOV AP
MALASHENKO IS
YAKOVCHUK KY
Citation: Ai. Rybnikov et al., THE STRUCTURE AND PROPERTIES OF METAL AND METAL-CERAMIC COATINGS PRODUCED BY PHYSICAL VAPOR-DEPOSITION, Journal of materials processing technology, 55(3-4), 1995, pp. 234-241
Authors:
KIM DH
Citation: Dh. Kim, A SIMPLE METHOD OF ANALYSIS FOR THE PRELIMINARY DESIGN OF PARTICULAR COMPOSITE LAMINATED PRIMARY STRUCTURES FOR CIVIL CONSTRUCTION, Journal of materials processing technology, 55(3-4), 1995, pp. 242-248
Authors:
TITOV AA
KROKHIN VA
ZHULANOV NK
MELNIKOV DL
Citation: Aa. Titov et al., PREPARATION OF CHEMICALLY ACTIVE POWDERS OF NIOBIUM AND TITANIUM-OXIDES AND SYNTHESIS OF DIELECTRIC CERAMIC MATERIALS, Journal of materials processing technology, 55(3-4), 1995, pp. 249-253
Authors:
AMIN SG
AHMED MHM
YOUSSEF HA
Citation: Sg. Amin et al., COMPUTER-AIDED-DESIGN OF ACOUSTIC HORNS FOR ULTRASONIC MACHINING USING FINITE-ELEMENT ANALYSIS, Journal of materials processing technology, 55(3-4), 1995, pp. 254-260
Authors:
LAY B
BOIVIN M
Citation: B. Lay et M. Boivin, THERMO-ELASTO-PLASTIC BEHAVIOR OF A METAL-MATRIX COMPOSITE AL-6061 SIC AND THE EFFECT OF A PRECIPITATE-FREE ZONE AROUND THE REINFORCEMENT/, Journal of materials processing technology, 55(3-4), 1995, pp. 261-267
Authors:
PUYANE R
Citation: R. Puyane, APPLICATIONS AND PRODUCT DEVELOPMENT IN VARISTOR TECHNOLOGY, Journal of materials processing technology, 55(3-4), 1995, pp. 268-277
Authors:
SUBRAMANYAM N
TSAI CT
Citation: N. Subramanyam et Ct. Tsai, DISLOCATION REDUCTION IN GAAS CRYSTALS GROWN FROM THE CZOCHRALSKI PROCESS, Journal of materials processing technology, 55(3-4), 1995, pp. 278-287
Authors:
TITOV AA
SHEVCHENKO AD
KOBELEVA SP
Citation: Aa. Titov et al., EFFECT OF THE PREPARATION CONDITIONS UPON THE STABILIZATION OF THE SUPERCONDUCTING PROPERTIES OF BI(PB) SRCACUO, Journal of materials processing technology, 55(3-4), 1995, pp. 288-291
Authors:
BURDUKOVSKY VG
KOLMOGOROV VL
MIGACHEV BA
Citation: Vg. Burdukovsky et al., PREDICTION OF RESOURCES OF MATERIALS OF MACHINE AND CONSTRUCTION ELEMENTS IN THE PROCESS OF MANUFACTURE AND EXPLOITATION, Journal of materials processing technology, 55(3-4), 1995, pp. 292-295